521,012.81 LAK
(3,741 JPY)
3 (3 Reviews)
Poor
My methods didn't workI bought it to make it easier to wash the VFR800F by rotating the front wheel when washing the car
・Of course, the Handlebar runs out on the Front, so you can't use the Rollers while turning stand's
It comes off the Roller part and almost falls off
But when I tried to wash the rear wheel, it was too late
You are supposed to lift up the Front so that the rear tire touches the ground and
It was in a state of spinning
(The veneer board is placed on the Center Stand
After that, it was too much of a hassle and I went back to the old method of lifting and turning the front tire by myself
Most Viewed Reviews Of TANAKA TRADING Other Maintenance Stands
Average
That's about itOn a heavy motorcycle, it is better than not having a car, but it takes a lot of effort to turn it (Laughs)
Cosmetically, I'm sure it's not a problem
I have two of them, and I'd like to use them both
Men really like to do this!
I thought I didn't need it, but I bought it too!View Detail
Very Good
I used impressions for the first timeFirst, open and check quality. The appearance worked ◎
Next, Roller hand-cranking operation check. One rotated slightly Smooth, but the other turned, although it turns, it did not rotate to Smooth feeling giggios. Whether the installation of the shaft is slightly Gap or whether there is a problem with Bearing.
Non-slip Rubber of Reverse side is firmly bonded and no problem. There seems to be no distortion of Frame, installation is also rattled and no problem.
Use immediately for Chain's Grease up. The place is Terrace in the garden and the ground is Concrete. When putting on slip Rubber was working firmly and was put on Smooth without gapping. Try turning Tire was seriously unexpected. I can put the rear wheel of 160 kg of weight and turn it with one hand, but I need a bit of strength. (Will it take more resistance when becoming Big bike ... sweat)
It was also an impulse of other people, but as I turn it, Tire steadily gaps to the edge of Roller and hits the Frame and does not turn around. Motorcycle itself is tilted, so it's not surprisingly .... Some way around the side I devise how to turn it Clear.
I think that it was good to buy because the work efficiency has been greatly improved compared to before. There is somewhat power, but working without Roller is all right..
As an aside, one thing I failed was one. I got over Motorcycle while working (Crying) What I mean is that if you set a little inclination of Motorcycle, you can suppress Gap of Tire ... and so on and halfway working on a 3 centimeter thick board on the Side Stand. Then Gap was suppressed to some extent and it became easy, so it was easy to roll it up, so we continued working while supporting Motorcycle. I thought that everything OK! I forgot that Concrete on the ground is a little inclined to Motorcycle's Right Side and I got a bit of a hand
It is the first time in this Motorcycle (Crying)
Mirror, Handlebar End, Front and rear Brake lever, footpeg, Exhaust System Silencer and Gijis got hurt (Crying)
Unfortunate happiness is that you have done only with scratches on this part.
Enemy Large Enemy watched it (Lol) (Crying)
It costs around the gold to cure everything, so it is around this time that we are searching for Wig Big as to whether we should exchange and repair the Grip end.View Detail
Other Reviews From Japan User(translated)
Excellent
Radipon handled in Mild?attachment
The CBR650R is mounted at the same position angle as the NORMAL.
However, when the handlebar was cut to the Left lock, it interfered with the interior cover next to the Meter, so the interior cover was cut away.
I also purchased a 45° angled banjo adapter for the mesh hose to accommodate the tension of the mesh hose.
・NORMAL (Reserve integrated horizontal master) Impressions of
No complaints on public roads. Familiar feel and very easy to handle.
However, when the brake is set to "hard brake," the rate of increase in braking force relative to the input seems to decrease, and the brake becomes more forceful.
Radipon (Reserve separate body portrait master) Impressions of
It was totally different from what I expected, my expectation was that it would feel like a Rear brake…
It is really a mild and easy-to-handle radipon.
On public roads, it feels like NORMAL! I wonder if it's because NORMAL is the same NISSIN?
But I felt the radipon effect from Breaking a little stronger, and
It can be hung up to a hard brake without effort.
I felt trust that this could stop.View Detail
Very Good
packtalk bold Attached MountI purchased this for use with multiple Helmets. 。
Mount included with the BOLD.
Microphone and speaker are not included and must be purchased separately.View Detail
Excellent
Grip replacementGrip that had been used for a long time was worn out and had to be replaced.
They are soft and dampen vibration.View Detail
Very Good
Works well in everyday life[How is it used?
Used to lick Screw loose.
Was the one you received as per Image?
As per Image.
How was your experience with it?
When used on a strongly tightened Screw, it can be safely and securely removed.
The licked Screw was removed.
It is also useful for DIY Screw removal.
[Points to note]
When used on a licked Screw, it is best to beat it in with a Hammer before use.View Detail
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING