*The foldable range is more limited than the stock step. *Because of its structure, the step bar is located outside of the stock step.The pedal will be inward relatively, so please drive carefully until you get used to it. *Some models may not be able to select all positions due to contact. *If the stock step pin is caulked, it needs to be machined down.
You can set the best step position according to the length of your feet and the size of your shoes, and reduce the feeling of tightness between the pedals and the step and around your knees. You can customize your ideal position by using COZY seat and height control rod to improve the footing.
●Clear anodized aluminum and black anodized aluminum finish. ●It's a stock step replacement type.Round step bar for easy load transfer. ●The step position can be selected from 8 positions (A-H, I position is the stock step position) within a radius of about 15mm from the stock step position.
Points of Attention
* If there may be an instruction manual included, it will be written in Japanese.
I immediately hit Knee Slider and wanted to convert it to Rear Sets, but the price was - - - I introduced the product here.
- About installation The most difficult thing is to remove the split Pin attached from the beginning. Other than that it is very easy.
- Traveling Check I am doing Gymkhana, but I can deepen the bank angle during the practice of figure 8 and it is enough to rub the shoes when entering.
I felt the ankle somewhat cramped at OEM's footpeg position, but it was adjusted and improved.
"I do not want to hit the Knee Slider soon!" "But I do not run Circuit" Those who are interested are by all means Recommendation.View Detail
Because Yamaha vehicle was a car with OEM footpeg Pin crimped, shaving the caulked part was troublesome, but if it was not even there (If it is Split Pin stop vehicle) It is a product that can be mounted very easily. Quality is also good, the point where footpeg position can be easily changed easily was good. However, although there are 8 Position alterable in the Instruction Manual, is Large Kim is 4 positives, is not 3 positive by fine adjustment? I could not understand the adjustment range.View Detail
It will attach with FZ1 in 2009.The place which there is no statement in conformity table, and the Manufacturer was asked, FZ1 is not suited.Future also has no schedule of development. Although there is a reply with and purchase was given up ... A target does not have any problem as a result of , and it has attached.Since there is uneasiness in use of a Back step and he does not want to purchase the circumference of the Step from experience which took time in the purchase of the Repair parts before, it is large satisfaction that the Position which used and got used also by CB and GSR which were owned in the past was able to be acquired.View Detail
In order that Rubber Division of STD might surely slide, the Step of the knurl process was looked for. This is very reasonable, and since it will hardly replace the Position of STD if it is attached without passing intermediate parts, it can be run comfortable. In those who do not want to use a Back Type so much, and a direction to ride on by an STD Position, it is recommended!View Detail
If the object for Yamahas is purchased and a wearing Peg is constructed to an R1Z in the upper position, a hacksaw will cut a Peg a pure Peg with a Rubber, and this time [ ] which are the same position and die length generally,
which orders a short Peg from a DAYTONA as long as processing changed into die length which resembled the Peg of the latest SS is troublesome, if a vehicle type is removed in part,Since the Peg is being fixed by the Crimp in many cases except the conformity vehicle type in , however description of item which are considered which it can equip a little if it is a Yamaha vehicle, with the necessity of flying the head of a Crimp with a Drill or a File -- since there is also no hard metal in particular -- which is not difficult -- even removing -- if it works using the pin which is attached after that if it carries out as a description -- completion -- incidentally a Grease and a Screw-lock agent (substitution in nail polish etc. is possible) need to be prepared separatelyView Detail
* The BEST and MUST store to find Japanese parts. * Register now for amazing deals and other special offers! *Over 800,000 listed items. It's hard NOT to find your parts.
SIGN IN TO WEBIKE JAPAN
Please enter email at least 6 characters.
Please enter a valid email address.
Email is already in use.
Your account has been banned.
Email address and/or password is not match.
Authentication with facebook fail.Please try again.
Please select How did you get to know about Webike Japan?
OR
YOUR ACCOUNT HAS BEEN CREATED!
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
Get on your grid by register your motorcycle! About our "Mybike" service
"Easier to Search Items" It helps you to search items to fit for your motorcycle!
"Get Much Valuable Information" It helps you to get special deals, newly listed items and closeouts about your motorcycle!
"Easy to Register" It requires only your motorcycle manufacturer, model name and model year!