[Components] Heat-shrinkable tube for grip protection
*Not for use with vehicles with small handlebars (Φless than 22.2), inch bars (Φ25.4), or vehicles with low battery capacity or power generation.(A voltage of 12.5V is required for start-up) *When installing the supplied extension sleeve, apply adhesive to the inside of the extension sleeve where it meets the grip, and crimp it firmly.Please note that extreme load on the extending sleeve may lead to the falling off of the extending sleeve or the breakage of the grip end and the extending sleeve. *Please understand in advance that you may feel lower temperature due to the heat radiation to the handlebars, bar ends and gloves, and cooling by the driving wind. *Use a heat gun to install the heat shrink tubing for grip protection provided.Also, when the grip heater is heated, the protective tube may soften and loosen due to the heat, so it is recommended to install it when the heater is not in use. *If the tube becomes loose after installation, heat shrink it again with a heat gun to make it tighter to the grip.If it still does not adhere, please remove the product as it may be the end of its life. *The total length of the protective tube has a tolerance of plus or minus 3mm due to its characteristics.The edge of the product may be slightly slanted, but this is not a defect. *The inner diameter of the right grip is Φ25.4.If the throttle sleeve of the vehicle to be installed has ribs, cut them to a height not lower than the inner diameter of the grip before installation.If the outer diameter of the throttle sleeve is smaller than the inner diameter of the grip and the throttle sleeve is loose, use the supplied aluminum seal to adjust the gap between the throttle sleeve and the grip. *This product may not be used for SUZUKI vehicles with low battery capacity and power generation, or HONDA vehicles with batteries less than 7S. *Yamaha vehicles with 4B5 or higher batteries can be used.
[Product Features] ・5-step temperature control with a compact switch.The 5-step temperature control is indicated by a 5-color LED lamp. ・The grip length can be adjusted to 115 / 120 / 130mm with 3 sizes of extended sleeves. ・The removable bar end cap is compatible with both bar end type and non-through type. ・Grip design for reliable maneuverability and thermal conductivity. ・The smallest diameter Φ33 provides a comfortable grip even if it is replaced with a regular grip. ・The nichrome wire is wound around the entire circumference of the hand to warm the entire palm. ・5 levels of temperature control and power consumption.*The temperature was measured at 25 degrees Celsius, no wind, and voltage 13.5V.The temperature may be lower than the measured value due to heat radiation to the handlebar, bar end, gloves, and cooling by stream. ・With a voltage suppression function, it is safe even at low voltage. ・When the voltage becomes less than 11.5V, the heating is automatically stopped, and when the voltage recovers, the heating is automatically restarted. ・Heat shrink grip protection tube" included!During the season when the grip heater is not used, this item is useful to prevent wear of the expensive grip heater.Simply cut to fit the grip length, attach to the grip, and heat shrink with a heat gun.
Points of Attention
* If there may be an instruction manual included, it will be written in Japanese.
Recently viewed products
Ratings & reviews for this product or related products
* The BEST and MUST store to find Japanese parts. * Register now for amazing deals and other special offers! *Over 800,000 listed items. It's hard NOT to find your parts.
SIGN IN TO WEBIKE JAPAN
Please enter email at least 6 characters.
Please enter a valid email address.
Email is already in use.
Your account has been banned.
Email address and/or password is not match.
Authentication with facebook fail.Please try again.
Please select How did you get to know about Webike Japan?
OR
YOUR ACCOUNT HAS BEEN CREATED!
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
Get on your grid by register your motorcycle! About our "Mybike" service
"Easier to Search Items" It helps you to search items to fit for your motorcycle!
"Get Much Valuable Information" It helps you to get special deals, newly listed items and closeouts about your motorcycle!
"Easy to Register" It requires only your motorcycle manufacturer, model name and model year!